Archive for April, 2014

Best Practices in Horticulture

by admin . 0 Comments

Composting
Composting is needed to remove waste components from the land and transforming it into a beneficial soil improver. No land is too little for a compost container. Composting is simpler to do in a container than in an open pile, where the stuff dries out too fast, slowing down the decomposition. The type of container is not that relevant – any container that guards for rain and wind, and keeps in some humidity, will develop great outcome in just a year. It’s important to build various layers of dry material – stems and stalks, and moist substance – grass and kitchen scraps, as an excessive of both will slow down the whole technique. Don’t add highly processed food, meat or fish products since draw in rats and negative bacteria.
Green manures
Green manures is plant life produced to defend and enrich the soil, rather than for picking for you to take home. They are cultivated on free land, usually out of season, and are cut down right after blooming. During developing they give shield from strong rain, drying winds and hot sunlight, which harm soil composition. When cut down and dug in, many add humus, enhance drainage and in some scenarios feed the soil. Later harvest show better progress and lessen the stress on soil.

 

Mulching
Mulching is the process of covering up the soil with a layer of materials that lowers evaporation but allows rainwater go through to the soil. This can be a penetrable groundcover sheet from a garden center or a dense layer of woodchip, and several other materials that are offered. Woodchip has the benefits of breaking down over time and adding humus to the soil, and it drastically lessens the deterioration caused by walking on newly-dug soil.
Watering
Taking the best out of the plants means watering thoroughly. You should water often and adequately, rather little and often – promote plants to grow deep roots rather than depending on a standard surface watering. Water the roots instead of the leaves – a damp conditions helps propagate disorders such as tomato blight. Rainwater is much healthier than tap water – it is usually warmer and holds no chlorine, while tap water can be considerably perfected by standing in a butt for a day.

Set up a Submersible Pond Pump in 4 Easy Steps

by admin . 0 Comments

Submersible pond pumps are used to establish water movement in a koi pond or any other type of pond by circulating oxygen. Pond pumps are easy to install for anyone and are generally used in ponds holding anywhere from 200 to 6000 gallons of water.

Step 1 – Selecting the Pump Size

It is important to know how many gallons of water the pond contains in order to figure out what size of pump is necessary. The pump box will normally suggest what size of pond the pump is made for, even though staff members at the expert water hobby stores will usually be able to make suggestions.

Step 2 – Getting the Pond ready

The submersible pond pump must never be positioned straight onto the ground of the pond as this may trigger debris and dirt particles to enter the pump and decrease its lifespan. Simply place a cinder block or a piece of wood where the pump will be placed. Position the submersible pump on top of this, also make sure the pump is entirely under water.

Step 3 – Setting Up the Pump

You need a flexible tubing for the pump. If you are using tubes from a reel, use a knife to cut the suitable length. This is where the water will be moved through to create motion.
Place the tube above the outflow part of the pump and make certain that it is firmly set up. Using a screwdriver, connect the hose clamp tightly to the pump.

Step 4 – Creating Movement

Two things left. The first thing to do is to simply place the hose over a waterfall and let it roll. This will allow the water from the pump to empty back into the pond.
The second thing is to place the hose to a fountain on the bottom where it will pump the water into the fountain. The water is then released back into the pond, establishing movement and therefore supplying oxygen.

After the hose is established into it’s place, you can plug the pump in to a connector. Look at the pond to verify that the water begins to show activity. If not, double-check all of the steps above to see if something you have been overlooked. If the water begins to move, it’s all good. When connected to a water fountain in a pond, submersible pond pumps allow to add visual beauty to your backyard and pond. An attractive look and grace for the whole garden is guaranteed.

Read more – http://petrowiki.org/Electrical_submersible_pumps